反应 #1178391

反应方程式

hydrogen

hydrogen

hydrogen

N,N-di-(4-biphenylyl)-benzylamine

chloroform

ethanol

hydrogen

→

di-4-biphenylylamine

收率 93.9%

溶剂

dichloromethane

反应条件

后处理

1. 1
   workup.ADDITIONwere added
2. 2
   workup.DISSOLUTIONto dissolve it
3. 3
   其他a three-way cock which was equipped a balloon
4. 4
   workup.STIRRINGAfter stirring for 30 hours
5. 5
   其他to separate the catalyst
6. 6
   过滤by filtration
7. 7
   其他Next, the solution obtained
8. 8
   其他was transferred into a separating funnel
9. 9
   洗涤washed with 50 mL of a sodium hydrogencarbonate saturated aqueous solution
10. 10
    其他the organic layer was separated
11. 11
    干燥dried on anhydrous potassium carbonate
12. 12
    过滤After filtered
13. 13
    workup.DISTILLATIONthe solvent was distilled off
14. 14
    workup.ADDITION50 mL of toluene was added to the resulting residue
15. 15
    其他recrystallization
16. 16
    其他Deposited crystal was separated by filtration
17. 17
    其他dried under vacuum at 50° C.

实验过程

Next, 120 mL of dehydrated toluene (manufactured by Hiroshima Wako Co., Ltd.), 4.08 mL of benzylamine (manufactured by Tokyo Kasei Kogyo Co., Ltd.) and 338 μL of tris-t-butylphosphine (a 2.22 mol/L toluene solution, manufactured by Aldrich Co., Ltd.) were added thereto through a rubber septum by means of a syringe and stirred at room temperature for 5 minutes. Next, the flask was set on an oil bath and gradually heated up to 120° C. while stirring the solution. After 7 hours passed, the flask was taken off from the oil bath to terminate the reaction, and it was left standing for 12 hours under argon atmosphere. The reaction solution was transferred into a separating funnel, and 600 mL of dichloromethane was added thereto to dissolve the precipitate. The organic layer was washed with 120 mL of a saturated brine and then dried on anhydrous potassium carbonate. The solvent of the organic layer obtained by filtering off potassium carbonate was distilled off, and 400 mL of toluene and 80 mL of ethanol were added to the resulting residue. The flask to which a drying tube was mounted was heated to 80° C. to completely dissolve the residue. Then, the flask was left standing for 12 hours and slowly cooled down to room temperature to thereby expedite recrystallization. Deposited crystal was separated by filtration and dried under vacuum at 60° C., whereby 13.5 g of N,N-di-(4-biphenylyl)-benzylamine was obtained. A single neck flask of 300 mL was charged with 1.35 g of N,N-di-(4-biphenylyl)-benzylamine and 135 mg of palladium-activated carbon black (palladium content: 10% by weight, manufactured by Hiroshima Wako Co., Ltd.), and 100 mL of chloroform and 20 mL of ethanol were added to dissolve it. Next, a stirring rod was put in the flask, and then a three-way cock which was equipped a balloon charged with 2 L of hydrogen gas was mounted to the flask. The inside of the flask was substituted 10 times with hydrogen gas by means of a vacuum pump. Lost hydrogen gas was newly charged to set again a volume of hydrogen gas to 2 L, and then the solution was vigorously stirred at room temperature. After stirring for 30 hours, 100 mL of dichloromethane was added thereto to separate the catalyst by filtration. Next, the solution obtained was transferred into a separating funnel and washed with 50 mL of a sodium hydrogencarbonate saturated aqueous solution, and then the organic layer was separated and dried on anhydrous potassium carbonate. After filtered, the solvent was distilled off, and 50 mL of toluene was added to the resulting residue to carry out recrystallization. Deposited crystal was separated by filtration and dried under vacuum at 50° C., whereby 0.99 g of di-4-biphenylylamine was obtained.

来源