反応 #11300

反応方程式

potassium phthalimide

2-chloroethyl vinyl ether

hydrazine hydrate

→

2-(vinyloxy)ethyl phthalimide

溶媒

methylene chloride

dimethyl foramide

—

1,4-dioxane(2) methanol

—

amine

反応条件

後処理

1. 1
   workup.ADDITIONthen poured into 800 mL
2. 2
   workup.DISTILLATIONdistilled water
3. 3
   ろ過filtered
4. 4
   洗浄washed with a large amount of distilled water
5. 5
   その他The recovered yellowish crystals where then recrystallized twice from methanol
6. 6
   その他to give white crystals, which
7. 7
   その他were then dried for 48 h under reduced pressure
8. 8
   その他Polymerization
9. 9
   workup.WAITto run for 3 h at −78° C.
10. 10
    温度to warm for ten minutes at RT
11. 11
    その他quenched with prechilled ammonia saturated methanol
12. 12
    その他The product was then evaporated to dryness under reduced pressure
13. 13
    その他to give the product polymers
14. 14
    温度This solution was then refluxed for 2 h
15. 15
    温度cooled to RT
16. 16
    その他the solvent was then removed under reduced pressure
17. 17
    温度refluxed for 60-minutes
18. 18
    その他The cooled solution was then transferred to 3,000 MW dialysis tubing
19. 19
    その他dialyzed (4×5 L) for 48 h
20. 20
    温度This solution was then frozen

実験手順

Amine-containing enol ether copolymers (i.e. Poly(alkyl enolether-co-vinyloxy ethylamine) Polymers: 2-(vinyloxy)ethyl phthalimide (ImVE) was prepared by reacting 2-chloroethyl vinyl ether (25 g, 0.24 mol) with potassium phthalimide (25 g, 0.135 mol) in dimethyl foramide (75 mL) using tetra-n-butyl ammonium bromide as a phase transfer catalyst. This reaction mixture was stirred at 100° C. for 6 h then poured into 800 mL distilled water, and filtered and washed with a large amount of distilled water. The recovered yellowish crystals where then recrystallized twice from methanol to give white crystals, which were then dried for 48 h under reduced pressure. Polymerization was carried out in anhydrous methylene chloride at −78° C. under a blanket of dry nitrogen gas in oven-dried glassware. The reaction was initiated by adding borontrifluoride diethyl etherate to ImVE, and a mixture of enol ethers. The reaction was allowed to run for 3 h at −78° C., and then allowed to warm for ten minutes at RT, and then quenched with prechilled ammonia saturated methanol. The product was then evaporated to dryness under reduced pressure to give the product polymers. The polymer was then dissolved in a 1,4-dioxane(2)/methanol mixture and 10 equivalents (eq.) of hydrazine hydrate per mole of amine present. This solution was then refluxed for 2 h, cooled to RT, and the solvent was then removed under reduced pressure. This solution was then brought up in 0.5M HCl, and refluxed for 60-minutes. The cooled solution was then transferred to 3,000 MW dialysis tubing and dialyzed (4×5 L) for 48 h. This solution was then frozen and lyophilized. The following polymers were generated using this procedure:

出典