Reacción #72408
ord-f5fe8760ffe94d7dac1e63c2e6994ad4
Ecuación de reacción
Reactantes
Reactivos
Condiciones de reacción
Tratamiento posterior
- 1Otroequipped with a Teflon-coated magnetic stirring bar
- 2OtroThe flask was evacuated
- 3Temperaturawhile being heated
- 4Otropurged with argon from the balloon
- 5workup.ADDITIONbefore addition of any reagents or solvents
- 6workup.ADDITIONAfter the addition
- 7workup.ADDITIONAfter the addition
- 8workup.STIRRINGstirred for 2 h
- 9Temperaturato warm to ambient temperature
- 10workup.STIRRINGstirred overnight
- 11ExtracciónThe organic product was extracted into an ether layer which
- 12Lavadowas washed with brine
- 13Secadodried over magnesium sulfate
- 14Filtraciónfiltered
- 15Concentraciónconcentrated in vacuo
- 16Otroto yield a residue
- 17workup.STIRRINGThe mixture was stirred at ambient temperature overnight
- 18LavadoThe alkaline solution was washed with ether
- 19OtroThe aqueous layer was separated
- 20Otrosubjected to in vacuo evaporation
- 21Otroto remove any residual ether
- 22Otroleading to the precipitation of a white solid
- 23workup.STIRRINGStirring
- 24workup.WAITwas continued for an additional 30 minutes
- 25Filtraciónthe precipitate was filtered off with suction through a sintered glass funnel
- 26LavadoThe collected solid was successively washed with water and two-50-ml of hexane
- 27Otrowas dried in vacuo at room temperature for 2 days
Procedimiento
All reactions reported in this example were carried out in an oven-dried three-necked, round-bottomed flasks equipped with a Teflon-coated magnetic stirring bar, copper iodide and a T-joint to which an argon-filled balloon had been attached. The flask was evacuated while being heated, then purged with argon from the balloon. This operation was repeated three times before addition of any reagents or solvents. To a stirred suspension of cuprous iodide (2.38 g, 12.5 mmol) in 30 mL of dried THF at ca −78° C. under argon, cyclopropylmagnesium bromide in THF solution (0.5M, 50 ml, 25 mmol) was added via syringe. After the addition had been completed, the mixture was stirred for 30 min and a solution of ethyl 7-iodoheptanoate (3.02 g, 10.63 mmol) in 10 ml of THF was added. After the addition, the reaction was allowed to warm to 0° C. and stirred for 2 h. It was allowed to warm to ambient temperature and stirred overnight. The reaction was poured into a saturated ammonium chloride solution. The organic product was extracted into an ether layer which was washed with brine, dried over magnesium sulfate, filtered, and concentrated in vacuo to yield a residue. 1H NMR confirmed the desired ethyl 7-cyclopropylheptanoate. GC indicated a single peak material. To the residue were added 25 mL of water and a 25 ml of a solution of NaOH (2N). The mixture was stirred at ambient temperature overnight. The alkaline solution was washed with ether. The aqueous layer was separated and subjected to in vacuo evaporation to remove any residual ether. The alkaline solution was acidified with an aqueous solution of HCl (2N) leading to the precipitation of a white solid. Stirring was continued for an additional 30 minutes and then the precipitate was filtered off with suction through a sintered glass funnel. The collected solid was successively washed with water and two-50-ml of hexane, and was dried in vacuo at room temperature for 2 days to afford 0.72 g (40%) of 7-cyclopropylheptanoic acid as a white solid. 1H NMR (400 MHz DMSO-d6) δ: 0 (m, 2H), 0.37 (m, 2H), 0.66 (m, 1H), 1.16-1.18(m, 2H), 1.34-1.50 (m, 6H), 1.78 (m, 2H), 2.20 (m, 2H), 12.0 (s, 1H). 13C NMR (100 MHz DMSO-d6) δ: 4.27, 10.65, 24.50, 28.61, 29.05, 33.64, 34.01, 174.43. Anal. Calcd for C10H18O2: C, 70.22; H, 10.66. Found: C, 70.05, H, 10.34 with a Karl Fisher water content %: 0.46.