Reaktion #90508

Reaktionsgleichung

DMF

2-(benzyloxy)-4-iodophenol

iodine

(R)-benzyl 2-(((benzyloxy)carbonyl)amino)-3-iodopropanoate

→

(S)-benzyl 3-(3-(benzyloxy)-4-hydroxyphenyl)-2-(((benzyloxy)carbonyl)amino)propanoate

Ausbeute 104.0%

Lösungsmittel

MTBE

Reaktionsbedingungen

Aufarbeitung

1. 1
   TemperaturCooled back to 10° C.
2. 2
   Sonstigezinc insertion (aliquot 2N HCl quench)
3. 3
   workup.WAITAfter 1 h
4. 4
   Sonstigeto 27° C.
5. 5
   Temperaturso cooled in a room temperature water bath back to 20-25° C.
6. 6
   workup.WAITAfter 15 h
7. 7
   Sonstige40 min, LC-MS
8. 8
   Sonstigeclean reaction
9. 9
   Filtrationfiltered the gray slurry
10. 10
    Waschenwashing the gray solid with MTBE (325+130 mL)
11. 11
    WaschenWashed the yellow filtrate with satd aq NH4Cl (325 mL, temp to 27° C. with a small amount of H2 evolution
12. 12
    Trocknenat pH ˜5-6) and brine (130 mL), dried (Na2SO4)
13. 13
    Sonstigeonly separating non-polar highly colored impurities and baseline material

Vorschrift

A slurry of zinc (47.0 g, 719 mmol) and DMF (325 ml) was stirred in a 2 L 3-neck round-bottom flask with magnetic stirring. The gray slurry was cooled to 16° C. in an ice bath and iodine (7.60 g, 29.9 mmol) was added (yellow to clear supernatant immediately with exotherm from 16 to 27° C.). Cooled back to 10° C. and added (R)-benzyl 2-(((benzyloxy)carbonyl)amino)-3-iodopropanoate (105 g, 240 mmol) portionwise over 10 min at <25° C. After an additional 10 min between 20 and 25° C., LCMS showed complete zinc insertion (aliquot 2N HCl quench). Added Pd2(dba)3 (0.457 g, 0.499 mmol), 2-dicyclohexylphosphino-2′,6′-dimethoxybiphenyl (0.410 g, 0.998 mmol), and 2-(benzyloxy)-4-iodophenol (65.1 g, 200 mmol) in one portion (no exotherm) and stirred at room temperature (start=2:30). After 1 h, an exotherm to 27° C. was observed, so cooled in a room temperature water bath back to 20-25° C. and stirred overnight. After 15 h, 40 min, LC-MS showed complete and clean reaction. Added MTBE (650 mL) and silica (65 g), stirred 15 min, and filtered the gray slurry, washing the gray solid with MTBE (325+130 mL). Washed the yellow filtrate with satd aq NH4Cl (325 mL, temp to 27° C. with a small amount of H2 evolution, at pH ˜5-6) and brine (130 mL), dried (Na2SO4), conc, and FCC (800 g column, 50-100% DCM/heptanes, then to 10% MTBE/DCM; only separating non-polar highly colored impurities and baseline material, upgrading HPLC pa % from 91 to 93 pa %) gave (S)-benzyl 3-(3-(benzyloxy)-4-hydroxyphenyl)-2-(((benzyloxy)carbonyl)amino)propanoate (106 g, 207 mmol, 104% yield) as a light brown oil. 1H NMR showed extra mass primarily CBz alanine Bn ester from protonation of excess alkylzinc during workup. Used without further purification in the next step, assuming quantitative yield. 1H NMR (501 MHz, DMSO-d6) δ 8.86 (s, 1H), 7.80 (d, J=8.0 Hz, 1H), 7.47-7.41 (m, 2H), 7.41-7.08 (m, 13H), 6.94 (d, J=2.0 Hz, 1H), 6.70 (d, J=8.0 Hz, 1H), 6.63 (dd, J=8.0, 1.9 Hz, 1H), 5.15-4.93 (m, 6H), 4.27 (ddd, J=9.7, 7.9, 5.5 Hz, 1H), 2.93 (dd, J=13.8, 5.5 Hz, 1H), 2.78 (dd, J=13.8, 9.8 Hz, 1H). MS (ESI) m/z 512 [M+H]+.

Quelle