تفاعل #76742

معادلة التفاعل

polyethylene

ammonium chloride

ethyl acetate

ammonia

3,3′-dimethoxybenzophenone

ammonia

→

beige product

المردود 69.4%

Ethyl 3,3-bis-(3-Methoxyphenyl)-3-hydroxypropionate

المردود 69.4%

المذيبات

ether

diethyl ether

ظروف التفاعل

المعالجة

1. 1
   أخرىA 2000 mL three-necked, round-bottomed flask equipped with a magnetic stirring bar
2. 2
   أخرىThe flask is furnished with, at one neck, a dry-ice cooled condenser with an oil bubbler on the vent
3. 3
   workup.ADDITIONto charge the components
4. 4
   أخرىThe interior of the flask is thoroughly flushed with nitrogen
5. 5
   أخرىthe flask is immersed in an acetone-dry ice bath
6. 6
   أخرىcondensed
7. 7
   أخرىwhereupon the flask is removed from the cooling bath
8. 8
   workup.ADDITIONA small piece of this lithium is dropped into the flask
9. 9
   workup.ADDITION0.2 g of ferric nitrate nonohydrate is added
10. 10
    workup.ADDITIONthe rest of the lithium is added
11. 11
    ترشيحwith filter paper
12. 12
    workup.ADDITIONbefore the addition
13. 13
    workup.WAITwaiting
14. 14
    workup.ADDITIONafter each addition until the transient blue color
15. 15
    workup.ADDITIONWhen addition
16. 16
    أخرىis obtained
17. 17
    أخرىA dark solution is formed immediately
18. 18
    workup.STIRRINGThe reaction mixture is stirred for 30 minutes
19. 19
    أخرىthe reaction is quenched
20. 20
    أخرىto evaporate
21. 21
    workup.ADDITIONWater (150 mL) is added
22. 22
    أخرىthe aqueous and ethereal phases are separated
23. 23
    استخلاصThe aqueous phase is further extracted twice with 100 mL portions of ether
24. 24
    غسيلwashed with saturated brine
25. 25
    أخرىThe ether is removed on a rotary evaporator
26. 26
    أخرى68 g of brown, partially crystallizing
27. 27
    أخرىoil is obtained
28. 28
    workup.DISTILLATIONThe oil is subjected to distillation with steam, which
29. 29
    أخرىremoves some ethyl acetoacetate by-product
30. 30
    درجة الحرارةThe remaing contents are cooled
31. 31
    أخرىthe excess water carefully decanted
32. 32
    workup.DISSOLUTIONThe solid residue is dissolved in ca. 200 mL of boiling ethanol
33. 33
    درجة الحرارةcooled
34. 34
    أخرىcrystallizes slowly), and
35. 35
    درجة الحرارةfurther cooled in an ice bath
36. 36
    أخرىThe crystalline product is isolated by filtration
37. 37
    غسيلwashed with a minimum of cold ethanol
38. 38
    أخرىdried in vacuum at 50° C

الإجراء التجريبي

A 2000 mL three-necked, round-bottomed flask equipped with a magnetic stirring bar is the reaction vessel. The flask is furnished with, at one neck, a dry-ice cooled condenser with an oil bubbler on the vent, and at another neck a rubber septum with a bored hole connected with a length of a polyethylene tubing attaching it to an ammonia cylinder. The centre neck serves to charge the components and is temporarily plugged with a stopper. The interior of the flask is thoroughly flushed with nitrogen and the flask is immersed in an acetone-dry ice bath. Ammonia flow is passed into the flask until ca 500 mL of liquid is condensed, whereupon the flask is removed from the cooling bath. 2.84 g (0.41 gat) of lithium wire is cut into approximately 1 cm pieces and kept under hexanes. A small piece of this lithium is dropped into the flask, creating an intense ink-blue colour. Ca. 0.2 g of ferric nitrate nonohydrate is added. After the blue color is discharged, the rest of the lithium is added, piece by piece, blotting each piece with filter paper before the addition, and waiting after each addition until the transient blue color disappears. When addition is complete a light grey suspension is obtained. At this point, 36.1 g (0.41 mole) of ethyl acetate are added in a single portion via a syringe or dropping funnel. A dark solution is formed immediately. The solution mixture is stirred for about two minutes, quickly followed by addition of 49.6 g (0.205 mole) of 3,3′-dimethoxybenzophenone as a solution in 100 mL of diethyl ether. The reaction mixture is stirred for 30 minutes, then the reaction is quenched by adding 22 g (0.41 mole) of ammonium chloride. Additionally, 250 mL of ether are added and ammonia is allowed to evaporate, either on its own (overnight) or by gentle warming in a room temperature water bath. Water (150 mL) is added and the aqueous and ethereal phases are separated. The aqueous phase is further extracted twice with 100 mL portions of ether. The ethereal layers are all combined and washed with saturated brine. The ether is removed on a rotary evaporator. Ca. 68 g of brown, partially crystallizing, oil is obtained. The oil is subjected to distillation with steam, which removes some ethyl acetoacetate by-product. The remaing contents are cooled and the excess water carefully decanted. The solid residue is dissolved in ca. 200 mL of boiling ethanol, cooled, seeded (crystallizes slowly), and further cooled in an ice bath. The crystalline product is isolated by filtration, washed with a minimum of cold ethanol and dried in vacuum at 50° C. The yield is 69%, 47 g of beige product are obtained. 1H NMR (CDCl3): δ 7.3-6.7 (m, ArH, 8H), 5.1 (s, OH, 1H), 4.1 (q, CH2—CH3, 2H), 3.75 (s, OCH3, 6H), 3.25 (s, CH2CO, 2H), 1.15 (t, CH2CH3, 3H).

المصدر